Lot No. LOT-5972 · offered November 18, 2026
Seeds, Crop Protection & FertilizerLot sheet
Wet Fall Raises Soybean Storage Risk in the Midwest
Wet fall increased soybean mold, sprouting and purple seed stain risk in parts of the Midwest. Guidance targets 13% moisture for affected beans, early elevator delivery and controlled bin aeration.
Market notes
- Beans with sprouting, mold or deep purple discoloration should be dried quickly to 13% moisture and delivered to the elevator first.
- Long-term storage moisture guidance is 11% to 12%; lower moisture increases bean-splitting risk.
- Cooled bins should hold 35°F to 40°F and remain within 10°F to 15°F of outdoor air.
- Winter inspections should occur every two weeks, with 15-to-30-second fan checks for musty odors.
- Spring warming should proceed in increments of 5°F or less, aiming for about 45°F in late spring and summer.

By Rebecca Stone
Growers should quickly dry soybeans showing sprouting, mold or deep purple discoloration to 13% moisture and prioritize elevator delivery, according to post-harvest guidance issued after a wet fall in parts of the Midwest.
Pioneer Field Agronomist Matthew Vandehaar said: “A lot of the initial quality concerns were the moldy soybeans, the ones that truly did get wet and molded within the pod.”
Vandehaar added: “We certainly had some smaller levels of sprouting that occurred on some of the upper pods, along with some purple seed stain. In general, it was the mold that concerned us most for storage.”
These were field observations, not a quantified assessment of Midwest-wide losses. No acreage, yield, price, basis, input-cost or financial-loss estimate accompanied them, so the moisture targets are operating guidance rather than a quantified estimate of damage.
What did the wet fall change?
The wet fall raised risk for three distinct conditions: beans wet enough to mold inside pods, sprouting concentrated in some upper pods, and purple seed stain. Vandehaar ranked mold as the leading storage concern, making early identification important before the crop reaches long-term storage.
How should growers clean and dry the crop?
- Clean before storage. Pre-storage screeners (equipment that separates larger debris) and cleaning operations can remove split beans and pockets of moisture and foreign material that shelter mold and fungus.
- Handle suspect beans first. Growers should dry soybeans with sprouted seeds, mold or deep purple discoloration quickly to 13% moisture to limit continued fungal metabolic activity (the biological process that allows mold to keep growing), then deliver them to the elevator first.
- Set a long-term target carefully. For extended storage, dry beans to 11% to 12% moisture. Lower moisture can increase splitting, and growers should account for moisture loss each time they move the soybeans.
These choices bear directly on farm margins because lower moisture can split beans and each transfer removes moisture and weight. Without drying-cost or basis figures, the guidance cannot rank the returns from immediate sale against extended storage.
What temperature should stored beans reach?
After drying, growers should cool grain bins to 35°F to 40°F as soon as outdoor temperatures cool. They should keep stored soybeans within roughly 10°F to 15°F of outside air and at nearly the same temperature throughout the bin, helping maintain a uniform grain mass and minimize moisture migration.
Without aeration (forced airflow through grain), cooler air near bin walls can fall to the bottom, push warmer, moist air up through the grain center and create condensation pockets. Aeration equalizes temperature and moves the grain closer to the outside-air temperature.
When is outside air suitable for aeration?
Outside air can either dry or rewet stored soybeans, so growers should check temperature and relative humidity (the percentage of water vapor in air) before running fans. An equilibrium moisture content table or calculator, which compares air conditions with the moisture level grain tends to stabilize at, can show whether aeration is suitable.
What should growers inspect during storage?
- Once the target winter storage temperature is reached, inspect soybeans every two weeks for moisture accumulation or crust development.
- Run fans for 15 to 30 seconds and check for a musty or rotting smell, which can signal deteriorating grain condition.
- Cover the fan intake when fans are not in use to avoid frost forming on the roof and melting into the seed.
- After snow and wind events, check whether snow has sifted into the bin.
- Use temperature and carbon dioxide monitors for additional information about stored-grain condition.
What safety rules apply to bin inspections?
Any bin entry requires proper grain-bin safety procedures. Before entering, shut down and lock out (disconnect and secure) electrical power, fans and unloading equipment. Never enter without another person nearby in case help is needed. Workers handling moldy grain should wear appropriate respiratory protection.
How should beans be warmed after winter?
For extended storage, growers should warm grain in increments of 5°F or less during spring to maintain quality. From late spring through summer, target a grain temperature of about 45°F by operating the fan on cool, dry nights.
For growers still holding beans, the immediate decisions are to identify damaged lots, move them toward delivery and keep remaining bins within the cooling and aeration limits while monitoring every two weeks. Spring warming will test whether winter storage preserved enough marketable weight and condition to protect farm returns.
via pioneer.com (Original)
More from Rebecca Stone
Show full bio
Market editor covering people, launches and day-to-day practice in Agribusiness coverage for industry professionals at Agribusiness Wire.
521 articles
Also in the yard
- Drier Forecast Offers Southwest Iowa Growers a Harvest Window
- Drought Devastates Soybean Yields Across Central Kansas
- USDA: 23% of U.S. corn harvested, trails five-year average
- Southwest Iowa Soybeans Show Seed-Coat Discoloration as Rain Delays Harvest
- Soybean Harvest Delays Raise Quality Concerns in Some Areas